Skip to content

Peptide Reconstitution Calculator

Enter how much peptide is in the vial, how much bacteriostatic water you add and the dose you want to measure. You'll see the concentration, the volume to draw and where it lands on a U-100 insulin syringe.

Work out your syringe units

Draw to

10 units

Volume
0.1 mL
Concentration
2.5 mg/mL
010203040506070809010010 u

The three formulas

  1. 1Concentration = vial amount ÷ water (mL)Arithmetic example: 5 mg ÷ 2 mL = 2.5 mg/mL
  2. 2Volume to draw = dose ÷ concentrationArithmetic example: 0.25 mg ÷ 2.5 mg/mL = 0.1 mL
  3. 3Syringe units = volume (mL) × 100Arithmetic example: 0.1 mL × 100 = 10 units

Track every dose for free

Save your vials, how you mixed them and every dose in PepLog, so the math is already done the next time you draw.

Create your account

How reconstitution math works

A freeze-dried peptide comes as a dry powder with a fixed amount printed on the vial, usually in milligrams. Adding bacteriostatic water turns the powder into a solution, and the amount of water decides how strong that solution is.

Divide the peptide by the water to get the concentration: 5 mg in 2 mL is 2.5 mg, or 2,500 mcg, in every millilitre. Divide the dose by the concentration to get the volume to draw, then multiply by 100 to turn millilitres into units on a U-100 syringe. With the same 5 mg vial and 2 mL of water, 250 mcg is 0.1 mL, which is 10 units.

Choosing a water amount

The water doesn't change how much peptide is in the vial, only how spread out it is. Less water makes a stronger solution and smaller draws; more water makes a weaker solution and larger draws.

Draws of 2 or 3 units are hard to read on a 100-unit syringe, so many people choose a water amount that puts a typical dose somewhere between 10 and 50 units. If the result is bigger than the syringe holds, use less water or split the draw. Whatever you pick, write it on the vial so every later calculation starts from the same number.

Reading a U-100 insulin syringe

U-100 means 100 units fill one millilitre, so each unit is 0.01 mL. A 1 mL syringe holds 100 units, a 0.5 mL syringe holds 50 and a 0.3 mL syringe holds 30. Smaller barrels space the marks further apart, which makes small draws easier to read.

Units measure volume, not peptide. The same 10 units can hold very different amounts depending on how the vial was mixed, which is why the concentration matters.

mg, mcg and why the unit matters

One milligram (mg) is 1,000 micrograms (mcg). Vials are usually labelled in mg while research doses are often written in mcg, and mixing the two up is the easiest way to be off by a factor of 1,000.

The calculator accepts either unit for the vial and for the dose and converts them before doing the math. Check the unit next to each number before you read the result.

Reconstitution questions

How many units is 250 mcg from a 5 mg vial?

It depends on the water. With 2 mL of bacteriostatic water the solution is 2,500 mcg per mL, so 250 mcg is 0.1 mL, or 10 units on a U-100 syringe. With 1 mL it would be 5 units, and with 3 mL it would be 15 units.

Does adding more water change the dose?

No. The amount of peptide in the vial stays the same. More water lowers the concentration, so you draw a larger volume to measure the same amount.

What is bacteriostatic water?

Sterile water with a small amount of benzyl alcohol (usually 0.9%) that slows bacterial growth. That is why it is commonly used for vials that are drawn from more than once.

Does the calculator work for any peptide?

The arithmetic is the same for any powder mixed with water: amount divided by volume gives concentration. The calculator knows nothing about a specific peptide and never suggests a dose; you enter every number.

What if the result is larger than my syringe?

The volume needed is more than one syringe holds. Mix with less water, choose a larger syringe or split the draw into two.

Is this medical advice?

No. It is an arithmetic tool for research and education. Talk to a qualified healthcare provider before using any peptide.